Skip to content

9am–5pm MT 1.559.715.6858

Cart
0 items

Blog

Raptor 660 +2 A-Arms: Fitment, Brake Lines and the Buying Checklist

05 Nov 2026 0 comments

A wider front-end kit is not just an A-arm purchase. Before ordering for a Yamaha Raptor 660, you need to understand the width notation, the parts that stay on the quad, and the supporting parts that must be sourced separately. Sorting those questions first gives your installer a clearer job and helps prevent an incomplete parts order.

Optional illustration omitted. Original conceptual illustration. Not measured, not CAD and not to scale.

Start with the ATV, then interpret “+2”

The APE RACING kit discussed here is for the 2001–2005 Yamaha Raptor 660, also identified as YFM660R. A familiar Raptor name is not enough to establish fitment for another model. Confirm the exact ATV and model year before comparing the kit with your existing front suspension.

For this kit, +2 means approximately two inches of extension on each side. Across both sides, that is approximately four inches of additional front track width, not two inches overall. Keep that distinction in mind when considering transport space and your usual riding routes. It is a description of the kit’s extension, not a promise of a particular final outside-tire measurement on every setup.

Budget for longer front brake lines

Longer front brake lines are required, and they are not included with this kit. Treat them as a necessary supporting purchase rather than an optional finishing touch. The existing stock lines are not long enough for the extended front suspension.

Have a qualified installer select suitable lines and verify safe routing, clearance and freedom from tension through steering and suspension movement before riding. A hose that appears comfortable with the ATV stationary does not establish that it will remain correctly routed throughout movement. This guide does not supply a hose length, routing procedure or brake-service instructions; those details need the correct installation information and professional assessment.

Separate included components from reused parts

The recorded package includes left and right upper and lower front A-arms, two stainless steel tie rods, pre-installed Delrin pivot bushings, pivot grease fittings, and upper and lower ball joints. The design reuses the OEM steel inner sleeves and dust caps. Ask your installer to assess those retained parts instead of assuming that every part removed from an older ATV is suitable for reuse.

The arms are made from 4130 chromoly steel tubing. Material identification is useful when comparing kits, but it is not a load rating or proof that the whole front end is ready for any impact. Buying decisions should still account for the ATV’s condition, correct assembly and the intended use.

Plan the setup without inventing shock changes

The existing product record specifies compatibility with stock-length front shocks, including replacements of the same length. That does not give you a new shock-length specification or establish that your particular aftermarket setup matches. Record what is currently fitted and have the installer check it against the kit information.

Do not order longer shocks simply because the A-arms are described as extended. Likewise, leave alignment settings and fastener torque to the applicable instructions and a qualified professional. A buying guide cannot replace the missing setup details for an individual machine.

Read the warranty as a limited warranty

The kit carries a limited lifetime warranty for the original purchaser against defects in materials and workmanship. Crash damage is excluded. The recorded exclusions also include hard-hit impact damage, misuse, improper installation and normal wear items such as bushings and ball joints. “Lifetime” should not be read as unlimited replacement coverage after riding damage.

Frequently asked questions

Does +2 mean two inches wider in total? No. This kit is approximately +2 inches per side, or approximately four inches wider across both sides.

Can I finish the purchase with the A-arm kit alone? Not without accounting for the required longer front brake lines, which are not included, and checking the parts intended for reuse.

Where can I review the specific kit? Compare this checklist with the APE RACING 2001–2005 Raptor 660 +2 A-arm kit and confirm the complete parts plan with your installer before ordering.

Yamaha and Raptor names identify vehicle fitment only. APE RACING is not affiliated with or endorsed by Yamaha Motor Co., Ltd.

Sources and scope

APE RACING specifications — SKU 82-I012-01. Product specifications reviewed October 28, 2026. This is a selection and identification guide, not a substitute for the applicable installation or service instructions.

General hose-clearance reference: Wilwood DS-470, page 4, on allowing suspension travel and steering movement. This is guidance for a different vehicle application, not Raptor-specific routing or kit-fitment instructions.

Prev post
Next post

Leave a comment

Please note, comments need to be approved before they are published.

Thanks for subscribing!

This email has been registered!

Shop the look

Choose options

Recently viewed

Edit option
Back In Stock Notification

Choose options

this is just a warning
Login
Shopping cart
0 items